In addition, use the anti- oxidant grease pack for the wire harness connectors. ![]() For additional protection, install the provided foam gasket between the keypad and the back box. For outdoor installations, use a UL Listed weatherproof back box and seal the wire entry locations with silicone and provide a drain hole. An appropriate range is typically between 48 and 52 inches on center off the floor. Mounting height can vary depending on requirements. To perform the self-test, with the unit powered up, press the following keys on the keypad: 7890123456 If all 12 keypresses are accepted, the keypad enters self-test mode. The keypad is designed to be flush mounted using a standard UL Listed single-gang electrical box. Testing the Keypad After installing the keypad, IEI recommends that you perform the keypad self-test once a year, to ensure that the keypad is working properly. The 2000e/eM keypads were evaluated by UL, in Wiegand Front End mode, for use only with the IEI Hub Max II and Hub MiniMax II products used in conjunction with the Wiegand Interface Module. The locking device and all inputs and outputs are connected to the control panel. The control panel maintains the users and programming options and makes all the access control decisions. When you enter a code on the keypad it is then sent to the control panel as Wiegand card data, depending on which format you've programmed it for. In Wiegand Front End mode, a separate Wiegand Access Control panel is required. The 2000e/eM keypads were evaluated by UL, in Secured Series Front End mode, for use only with the IEI Hub Max II and Hub MiniMax II products. The locking device and all inputs and outputs are connected to the controller. The IEI Secured Series Controller maintains the users and programming options and makes all the access control decisions. In Secured Series Front End mode, an IEI Secured Series Controller is required. The lock and all other inputs and outputs are connected directly to the keypad. In this mode, all the users and other programming options are maintained within the keypad and no additional controller is required. Refer to the programming section for details about selecting each mode.īy default, the keypad is programmed for Standalone Mode. Below is a brief explanation of each mode. The 2000e/2000eM keypad has three operating modes: Standalone Mode, Secured Series Front End Mode and Wiegand Front End Mode. Questions can also be submitted through our website atĮnd User: Please contact your service company. ![]() Service Company: To contact IEI’s Technical Support department, call 1- 80, Monday through Friday. – 22 AWGġ.0x (“1” is the major version “0” is the minor version “x” is a minor version, reserved for bug fixes, which is indicated with a letter, such as “a”.) Note: This is total maximum current including keypad and output module.ġ000 Ft. The 2000e/2000eM keypad has three operating modes: Standalone Installation & Programming Instructions.Keypad with Output Expansion Module (2000- 8EX) Current Requirements (Max) Table of an appropriately rated linear DC Power Supply (12-15 VDC) (filtered and regulated recommended). High quality performance keypad Illuminated hardened back-lit keys for long term durability Key press feedback via built-in sounder and yellow LED Program Connecting multiple units allows transferring programming data (either the directory entries only or the entire User Manual Installation Manual Literatureprox.pad Installation/Programming Manual. FilesIEIHubManagerPro7ProgramUtilitiesUSB_DriverFTDI_XP-2K-2003 or C.FTDI_XP-2000-Vista. required for manual or batch programming UNIT CAPACITY Users 2,000 users maximum The prox.pad plus unit uses radio frequency to transfer power to and 2000 Series e/eM Keypad Programming and Installation Manual ends to IEI Secured Series Access Control Systems and Wiegand Front When using the DTD as a transfer device in DTD Mode, website at for the latest version of this manual. ![]() Linear iei 2000e manual lymphatic drainage Download / Read Online transfer Manual de refrigeracion copeland pdf files Hk 450 tt pro fbl manual meat 2000 Connecting multiple units allows transferring programming data (either the directory entries only or the entire User Manual Installation Manual Literature ProxPad Plus Users Manual details for FCC ID PHUPPP made by International IEI assumes no responsibility for any errors that may appear in this manual. Iei keypad 232 manual iei 212r/se programmingiei prox pad plus software download iei 212se keypad programming manual iei 212i keypad reset iei 2000e keypad programming manual iei 212w keypad programming manual iei 232i programming manual LINEAR IEI 2000E MANUAL TRANSFER > READ ONLINE LINEAR IEI 2000E MANUAL TRANSFER > DOWNLOAD NOW
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |